15mm & 22mm Grakob RCT3 Plastic Plumb Thumbs Radiator Capping Tool

The 15mm & 22mm Grakob RCT3 Plastic Plumb Thumbs Radiator Capping Tool is a versatile tool that can be used for a variety of plumbing tasks, including removing and installing radiator caps, as well as capping off pipes. It is made from high-quality plastic and is designed to be durable and long-lasting.Good:Versatility: The tool can be used for a variety of plumbing tasks, making it a versatile addition to any toolkit.Durability: The tool is made from high-quality plastic and is designed to withstand wear and tear.Easy to use: The tool is easy to use and can be operated by one person.Safe: The tool is designed to be safe for use and will not damage pipes or fittings.Affordable: The 15mm & 22mm Grakob RCT3 Plastic Plumb Thumbs Radiator Capping Tool is an affordable option for plumbers of all levels of experience.Light weight: The tool is lightweight and easy to carry, making it convenient to take with you to job sites.Bad:Not as durable as some other tools: The tool may not be as durable as some other tools, such as brass tools.May not be suitable for heavy-duty use: The tool is not designed for heavy-duty use and may not be suitable for use on older or corroded pipes.May not be as effective on some types of pipes: The tool may not be as effective on some types of pipes, such as copper pipes.Some users have reported that the tool can be difficult to use on small or tight spaces: The tool may be difficult to use on small or tight spaces, such as behind radiators.Some users have reported that the tool can be difficult to use with worn-out or damaged caps: The tool may be difficult to use with worn-out or damaged caps.Overall:The 15mm & 22mm Grakob RCT3 Plastic Plumb Thumbs Radiator Capping Tool is a good option for plumbers who are looking for a versatile, affordable, and easy-to-use tool for removing and installing radiator caps. However, it may not be as durable as some other tools and may not be suitable for heavy-duty use.

These products are a valuable addition to any tool box, especially if you don't want to drain a radiator before removal.The thread catches quickly and makes a full and effective seal against water leakage, resulting in minimal loss of contaminated water from your heating system.Word of warning - the radiator will be very heavy when lifting off the wall brackets due to retained water.

I work as a heating engineer and use these every day and they’re a life saver! Very durable but only reason I didn’t give 5 star is that they easily cross thread which can be avoided if you’re tightening correctly but many times it’s hard when you’re doing it in a tight spot. Nevertheless it’s a must for Heat engineers / Plumbers or diy enthusiasts!

A very useful addition to the tool cupboard. I had help my dad remove a radiator temporarily while they got some work done on a bit of damp. These made the job so much easier than it would have been before.Close off the lockshield valve, remove the TRV and use a decorators cap to close the valve. Bleed the excess pressure (and water) out via the bleed valve at the top of the rad. One side at a time with a tub underneath to catch any drips, disconnect the valve from the rad, pull the valve away from the rad just enough to slip this in place and attach it to the rad tail, repeat for the other side. Then the whole rad (including the water inside) can be moved outside and emptied into a drain, rinsed through with water, or even stored with the water in for now, etc. So much easier than emptying it one tub at a time and then stuffing a rag in each side so it doesn't drop as you carry it through the house. Belt and braces, we put a 1/2" bsp blanking cap on both of the valves so that if the valve wasn't 100% closed the few drops of water that got through wouldn't get out onto the floor. Not really needed, but for about £2 for the blanking caps, it wasn't going to break the bank, for another layer of protection.Only downside is that you have to carry the extra weight of the water (though in reality it's not actually that much extra weight on a normal Type 21 or 22 rad.Personally I think they are a bit overpriced for two bits of plastic that are this size, but they do the job well.

Brilliant work perfectly saves a lot of mess

Brilliant tool.

Best tool for capping of radiators quick and simple to get the job done, no mess no stress.